Skip to content
Specialized Packaging Market Intelligence and Strategic AdvisoryPackaging Intelligence. Clearer Decisions. Stronger Growth.

SPI LedgerNews analysis

Henkel Sustainable Impact Report 2025: 28% recycled plastic, 88% designed for recycling, and the rules ahead

The Henkel Sustainable Impact Report 2025, published on 14 April 2026, gives 28% recycled plastic in consumer goods packaging against a 2025 goal of more than 30%, and 88% of packaging designed for recycling or reusability against 100%; the same day Henkel set new 2030 targets of at least 35% recycled plastic and 100% designed for recycling.

By the SPI teamPublished Updated 20 min readFigures as of 10 Nov 2026

Henkel packaging in three numbers: 28% recycled plastic, 88% designed for recycling, and 2.4 points a year now needed on design

28%

Recycled plastic in consumer goods packaging, 2025

Goal was more than 30%

Henkel

88%

Packaging designed for recycling or reusability, 2025

Goal was 100%

Henkel

2.4 points

Yearly gain needed to reach 100% designed for recycling by 2030

Against 0.33 a year from 2022 to 2025

SPI calculation

Source: Henkel Sustainable Impact Report 2025, pp. 28 and 50; Henkel release, 14 April 2026; SPI calculation (SPI summary), checked 22 Nov 2026.

The pace is the 12 points between 88% and the 100% target for 2030, spread over five years, by SPI's calculation. Henkel does not state a yearly pace.

The recycled share has risen 12 points since 2022, so the new target needs only 1.4 points a year, by SPI’s calculation. The design-for-recycling share has moved 1 point in three years, which is why it, and not recycled content, is the measure that the EU Packaging and Packaging Waste Regulation (PPWR) and California’s SB 54 will test hardest.

Exhibit 1Henkel missed all three 2025 packaging goals it reports against, and kept two of them, with new wording, for 2030
Measure2025 goal2025 result2030 targetExcluded from the measure
Recycled plastic in consumer goods packagingMore than 30%28%At least 35%Dangerous goods (2030 footnote)
Packaging designed for recycling100% (or reusability)88%100% (recycling only)Products whose ingredients or residue may affect recyclability; dangerous goods (2030)
Paper and cardboard recycled or from sustainable origins100%98%No numeric targetNot stated
Fossil-based virgin plastic50% cutNot reportedNo numeric targetNot stated

Source: Henkel Sustainable Impact Report 2025, pp. 21, 28, 29 and 50; Henkel release, 14 April 2026 (SPI summary), checked 22 Nov 2026.

Results are Henkel's own figures for fiscal 2025, data closed on 31 December 2025, not audited by SPI. The 2025 recycled plastic goal was paired with a 50% cut in fossil-based virgin plastic; the report gives no achieved figure for that cut. Exclusions are Henkel's footnotes.

Executive summary

Henkel published its Sustainable Impact Report 2025 on 14 April 2026. The packaging chapter reports 28% recycled plastic in consumer goods packaging, 88% of packaging designed for recycling or reusability, and 98% of paper and cardboard recycled or from sustainable origins. Each figure sits below the 2025 goal the company had set, and the report gives no achieved figure for its fourth aim, a 50% cut in fossil-based virgin plastic.

The same day Henkel announced its 2030 targets: at least 35% recycled plastic in packaging for consumer products, excluding dangerous goods, and 100% of packaging designed for recycling, excluding dangerous goods and products whose ingredients or residue may affect recyclability. Ledger 29 set Henkel beside three peers and Ledger 60 covered its refill programmes; this piece reads the report year by year and rule by rule.

The two headline metrics are moving at very different speeds. Henkel’s releases give a recycled plastic share of about 16% in 2022, 19% in 2023, 25% in 2024 and 28% in 2025, an average gain of 4.0 points a year. The design-for-recycling share was about 87% in 2022, 89% at the end of 2024 and 88% in 2025. By SPI’s calculation the 2030 recycled target needs 1.4 points a year, a third of the recent pace, while the design target needs 2.4 points a year, about seven times the 2022 to 2025 pace.

The rules ahead test different things from the ones Henkel counts. PPWR Article 7 sets recycled content per plastic part, averaged per plant and year, and counts only post-consumer plastic; the German text puts the 2030 floor for plastic packaging outside the food-contact and drinks-bottle categories at 35%, and the Parliament’s summary puts the 2040 floor at 65%. Henkel’s European detergent bottles already carry 65%, while its Adhesives Construction business reached 12% in 2025. PPWR Article 6 grades recyclability from 2030 with no exclusion for products whose residue harms recycling. California’s SB 54 asks for 10% less single-use plastic from 1 January 2027, 52 days after 10 November 2026, a measure Henkel’s report does not publish.

For suppliers and customers of Henkel, the useful reading is that the group average is safe to 2030 but the parts are not. Detergent bottles are ahead of the law; adhesive and construction packs, the excluded products and the virgin plastic baseline are where the work and the data requests will land.

Key findings

  1. Henkel reports 28% recycled plastic in consumer goods packaging for 2025 against a goal of more than 30%, and in March 2025 it had said it expected to reach 30% by the end of 2025 (Sustainable Impact Report 2025, p. 28; Henkel release, 11 March 2025).
  2. The recycled share rose from about 16% in 2022 to 28% in 2025, by SPI’s calculation an average of 4.0 points a year; the 2030 target of at least 35% needs 1.4 points a year (Henkel releases, 2023 to 2026).
  3. The design-for-recycling share went from about 87% in 2022 to 89% at the end of 2024 and 88% in 2025; reaching 100% by 2030 needs 2.4 points a year, about 7.2 times the 2022 to 2025 pace, by SPI’s calculation.
  4. SPI analysis: Henkel’s 2030 recycled target of 35% equals the PPWR 2030 floor for plastic packaging outside the contact-sensitive and drinks-bottle categories in the German text of Article 7(1)(d), but Henkel’s figure is a portfolio average and the PPWR floor applies to each plastic part.
  5. European liquid laundry bottles up to 3 litres for Persil, Spee, X-TRA and Le Chat carry 65% post-consumer recycled (PCR) plastic, adding 541 tonnes of PCR in 2025, which already matches the 65% PPWR floor for 2040 in the Parliament’s summary (report, p. 44).
  6. Henkel’s Adhesives Construction business reached 12% recycled content in the plastic packaging of its consumer products in 2025 and aims for 45% by 2028; by SPI’s calculation that is 11.0 points a year, 7.9 times the group pace needed to 2030 (Henkel sustainable packaging page).
  7. Henkel reports no virgin plastic tonnage and no achieved fossil virgin plastic cut, so the report cannot be read against SB 54’s 10% source reduction step for 2027 or its 25% step for 2032 (CalRecycle producer guidance).

Henkel Sustainable Impact Report: what the 2025 packaging chapter says

The report is Henkel’s annual sustainability statement for fiscal 2025. Its foreword is dated Düsseldorf, 14 April 2026, and page 2 states that data and facts closed on 31 December 2025. Packaging appears in four places: the Consumer Brands summary on pages 16 and 18, the target tables on pages 21, 28 and 29, a product example on page 44, and the circularity chapter on pages 48 to 50.

Page 50 sets out a packaging strategy in three pillars. The first, intelligent design, says design for recycling is considered early in development and that packaging material is cut to a minimum without compromising product quality or safety. The second, sustainable sources, covers recycled content and renewable materials such as paper, cardboard and bio-based plastics. The third, closing the loop together, covers partnerships to improve recycling infrastructure and an ambition, framed by extended producer responsibility (EPR), to prevent unregulated disposal of packaging waste.

The scorecard on page 28 is short. It lists four packaging lines for 2025, each with its goal and outcome, and Exhibit 1 sets them out. Three carry a number; the fourth, no plastic waste into nature, is an ambition with no metric. The report does not use the word missed. It prints the goal and the result side by side.

Two scopes run through the chapter. Page 18 says almost 100% of Consumer Brands packaging is designed for recycling or reuse, while pages 28 and 48 give 88% for the measure Henkel reports against its target. Ledger 29 noted the gap; the report still does not reconcile it. SPI analysis: the likeliest reading is that the 88% covers packaging across business units, including Adhesive Technologies, while the near 100% covers Consumer Brands alone, but the report does not say so and SPI has not yet confirmed the boundary.

What the report leaves out matters as much. Its packaging pages give no packaging tonnage, no split by material, no regional figures, no fossil virgin plastic result and no reusable packaging share. Nor does the packaging chapter refer to the PPWR by name, although the Regulation has applied since 12 August 2026 and the report was published four months before that date.

Five years of figures: the recycled share climbs, the design share stalls

Henkel has reported both measures every spring since at least 2023. Exhibit 2 puts the recycled plastic series together from Henkel’s own releases and the 2025 report.

Exhibit 2Henkel's recycled plastic share rose from about 16% to 28% in three years, faster than its 2030 target needs Unit: % recycled plastic in consumer goods packaging
Exhibit 2. Henkel's recycled plastic share rose from about 16% to 28% in three years, faster than its 2030 target needs4 bars. Largest: 2025, 28.20222022: 16 % recycled plastic in consumer goods packaging1620232023: 19 % recycled plastic in consumer goods packaging1920242024: 25 % recycled plastic in consumer goods packaging2520252025: 28 % recycled plastic in consumer goods packaging28Exhibit 2. Henkel's recycled plastic share rose from about 16% to 28% in three years, faster than its 2030 target needs4 bars. Largest: 2025, 28.20222022: 16 % recycled plastic in consumer goods packaging1620232023: 19 % recycled plastic in consumer goods packaging1920242024: 25 % recycled plastic in consumer goods packaging2520252025: 28 % recycled plastic in consumer goods packaging28

Source: Henkel releases of 7 March 2023, 4 March 2024 and 11 March 2025; Henkel Sustainable Impact Report 2025, p. 28 (SPI summary), checked 22 Nov 2026.

Henkel gives 2022 as around 16%. Each year is Henkel's figure as first published, not restated by SPI. The 2025 goal was more than 30%; the 2030 target is at least 35%.

Show the data
Exhibit 2. Henkel's recycled plastic share rose from about 16% to 28% in three years, faster than its 2030 target needs (% recycled plastic in consumer goods packaging)
YearRecycled plastic share (%) (% recycled plastic in consumer goods packaging)
202216
202319
202425
202528

The yearly steps were 3, 6 and 3 points. The 6 point jump in 2024 is the largest, and in March 2025 Henkel said it expected to reach 30% by the end of that year. It reached 28%. By SPI’s calculation the average gain from 2022 to 2025 is 4.0 points a year, and the gain in the last year was 3.0 points.

The design-for-recycling series tells a different story. Exhibit 3 shows the figures Henkel has published and the words it used for each.

Exhibit 3Henkel's design-for-recycling share has stayed between 87% and 89% since 2022, and its wording has changed twice
YearShare (%)Henkel's wording
202287Designed for recycling and reuse, around 87 percent
2023no dataNot stated in the 2024 release
202489Consumer packaging designed for recycling
202588Packaging designed for recycling or reusability
2030 target100Packaging designed for recycling

Source: Henkel releases of 7 March 2023, 4 March 2024 and 11 March 2025; Henkel Sustainable Impact Report 2025, pp. 28 and 48 (SPI summary), checked 22 Nov 2026.

Each figure is Henkel's own, as published. The 4 March 2024 release gives no figure for 2023, so that row is marked no data. Scopes differ by year as the wording column shows; SPI has not restated them on one basis.

Three words changed in four years: reuse, consumer and reusability. The 2025 figure of 88% is one point below the 89% Henkel gave for the end of 2024, and the wording moved from consumer packaging to packaging. Whether the dip reflects a wider scope, a change in the portfolio or a change in method is not explained in the report. SPI analysis: a measure that has held between 87% and 89% for three years is close to a plateau, and the last 12 points are usually the hardest, because they are the formats with no recyclable mono-material alternative yet.

Exhibit 4 turns both series into the pace each 2030 target needs.

Exhibit 4SPI calculation: the 2030 recycled target needs a third of Henkel's recent pace, the design target seven times it
Measure2025 result (%)2030 target (%)Past pace, 2022 to 2025Needed pace, 2025 to 2030Ratio
Recycled plastic share28.0035.004.001.400.35
Designed for recycling88.00100.000.332.407.20

Source: SPI calculation from Exhibits 2 and 3 (SPI summary), checked 22 Nov 2026.

Past pace = change from 2022 to 2025 divided by three years. Needed pace = 2030 target minus 2025 result, divided by five years. Ratio = needed pace divided by past pace, computed on the unrounded past pace of one point in three years. Henkel publishes no yearly path. Both measures are Henkel's own, on their own bases.

The asymmetry is the main finding of this piece. A recycled share target that asks for a third of recent progress leaves room for price shocks in recycled resin. A design target that asks for seven times recent progress cannot be met by continuing what Henkel already does; it needs reformulated packs, new materials or a narrower scope.

The 2030 targets and their exclusions

The 14 April 2026 release states the two packaging targets in one paragraph.

“By 2030, the share of recycled materials is planned to reach at least 35 percent, up from the current level of 28 percent.”

Henkel, company release, Henkel announces new sustainability targets for 2030, 14 April 2026

The release speaks of recycled materials; the report’s target table on pages 21 and 29 speaks of recycled plastics in packaging for consumer products. SPI reads the two as the same target, with the report’s wording as the defining one. The release also says Henkel aims for 100% of its packaging to be designed for recycling by 2030, already reaching 88%, and gives no definition or exclusion; the footnotes are in the report.

The footnotes do real work. The recycled plastic target excludes dangerous goods. The design target excludes dangerous goods and products whose ingredients or residue may affect recyclability or pollute recycling streams. Exhibit 5 compares those boundaries with the boundaries the PPWR draws.

Exhibit 5Henkel's exclusions and the PPWR's overlap on dangerous goods but not on product residue
Point of comparisonHenkel 2030 targetPPWR rule
What counts as recycledRecycled plastics (source not split in the report)Post-consumer recycled plastic only (Article 7)
Unit of measureShare across consumer products packagingEach plastic part, averaged per plant and per year
Dangerous goods, recycled contentExcludedListed among exceptions in the EUR-Lex summary
Dangerous goods, recyclabilityExcludedExempt only for packaging used to transport dangerous goods
Products whose residue harms recyclingExcluded from the design targetNo such exemption recorded
Small partsNot addressedPlastic parts under 5% of unit weight exempt from Article 7
ReuseDropped from the design measureSeparate re-use targets in Article 29

Source: Henkel Sustainable Impact Report 2025, pp. 21, 28 and 29; Commission Notice C/2026/3084; EUR-Lex summary of Regulation (EU) 2025/40; European Parliament Legislative Observatory summary; SPI tracker records PR-EU-004 and PR-EU-010 (SPI summary), checked 22 Nov 2026.

SPI analysis, not legal advice. PPWR exemptions are as recorded in SPI's tracker from the Commission Notice and the EUR-Lex summary; SPI has not yet confirmed them against the Official Journal text. Henkel's definitions are its own.

SPI analysis

The residue exclusion is the line to watch. A cleaning product or adhesive whose leftover contents contaminate a recycling stream is outside Henkel’s 100% target, but nothing in SPI’s records of the PPWR exempts it from Article 6. If the share of such products is material, Henkel’s own target could be met while some of its packs still fail the EU test.

PPWR recycled content: where Henkel's product lines sit

Article 7 of Regulation (EU) 2025/40 sets minimum post-consumer recycled content for plastic packaging in two tiers. SPI’s tracker record PR-EU-004 has confirmed the 30% figure for single-use plastic drinks bottles in 2030. For the other categories this piece relies on the German text of Article 7(1) as reproduced by LX Gesetze, an unofficial source, which gives 30% for contact-sensitive packaging made mainly of PET, 10% for other contact-sensitive plastics, 30% for single-use plastic drinks bottles and 35% for all other plastic packaging. The European Parliament’s summary of its first-reading position lists the 2040 floors as 50%, 25%, 65% and 65% in the same categories. Ledger 17 covers the full Article.

Henkel’s detergent bottles, adhesive tubes and construction product packs are not drinks bottles and, in SPI’s reading, not contact-sensitive in the PPWR sense, so they fall in the last category: 35% in the 2030 tier and 65% in the 2040 tier. Exhibit 6 sets Henkel’s product-level figures against those floors.

Exhibit 6Henkel's European detergent bottles already meet the 2040 floor; its construction adhesive packs are below the 2030 one
Product line and regionHenkel figure (%)Against the 35% floor for 2030 (points)Against the 65% floor for 2040 (points)
Persil, Spee, X-TRA, Le Chat bottle bodies up to 3 litres, Europe65+300
Ceresit Fester A, selected packs, MexicoMore than 65Above +30Above 0
Ceresit CE40 and CE43, Eastern EuropeMore than 50Above +15Below 0
Liquid laundry bottle bodies, North AmericaAt least 50At least +15At least -15
Bottles of 4 litres and smaller, Australia and New Zealand75+40+10
Adhesives Construction, consumer products, global, 202512-23-53
Adhesives Construction target, 202845+10-20
Henkel group average, 202528-7-37

Source: Henkel Sustainable Impact Report 2025, p. 44; Henkel sustainable packaging page; German text of PPWR Article 7(1)(d) as reproduced by LX Gesetze; European Parliament Legislative Observatory summary (SPI summary), checked 22 Nov 2026.

Henkel figures are its own for the product lines named, mostly 2025. PPWR floors apply only to packaging placed on the EU market, and only per plastic part; non-EU lines are shown for comparison of scale, not compliance. Points against the 2030 floor = Henkel figure minus 35, by SPI's calculation. Not legal advice.

The table carries three messages. First, the European laundry bottles, the format Henkel most often cites, are already at the 2040 level, and the switch added 541 tonnes of PCR in 2025, with Henkel estimating about 600 tonnes of CO2 avoided a year. Second, the group average of 28% hides a spread from 12% to 75%, so the average says little about any one part. Third, construction adhesives are the gap: at 12% in 2025 they are 23 points under the 2030 floor, and the 45% target for 2028 would clear it only if it is met in the packs sold in the EU.

The Ceresit CE40 and CE43 lines are named for Eastern Europe, which can include EU Member States; Henkel does not say where they are sold, so SPI has not yet confirmed which of those packs fall under Article 7.

In practice: Persil, Spee, X-TRA and Le Chat in Europe.

Henkel reports that liquid laundry detergent bottle bodies up to 3 litres for these four brands are made with 65% PCR plastic. The bottle body is the main plastic part, but caps and sleeves are separate parts under Article 7 and each must meet its own floor unless it weighs less than 5% of the unit. Henkel’s figure covers the bottle body only. SPI has not yet confirmed the cap and sleeve content.

In practice: Adhesives Construction.

Henkel’s sustainable packaging page says the business reached its target of 12% recycled content in the plastic packaging of its consumer products globally in 2025 and aims for 45% by 2028. By SPI’s calculation that is 33 points in three years, or 11.0 points a year, and 3.75 times the 2025 level. Ceresit Fester A in Mexico, with more than 65%, shows the format can carry high PCR; the question is how fast it spreads across the range.

PPWR recyclability: the 88% meets the A, B and C grades

Article 6(1) of the PPWR says all packaging placed on the market shall be recyclable. The Commission’s guidance reads that sentence as applying from 12 August 2026, and the graded test of design for recycling from 1 January 2030 or 24 months after the Article 6(4) delegated acts enter into force, whichever is later (PR-EU-010). Packaging below grade C is treated as technically non-recyclable, the floor rises to grade B from 1 January 2038, and a test of recycling at scale follows from 2035. Ledger 66 explains the grades.

Henkel’s 88% is not a PPWR grade. It is the company’s own assessment, against its own criteria, with its own exclusions. The PPWR grades do not exist yet in force: the delegated acts with the criteria are due by 1 January 2028, 417 days after 10 November 2026. Until then, SPI’s record notes that manufacturers keep meeting the essential requirements carried over from the 1994 directive, using standards such as EN 13430:2004.

SPI analysis

Three groups of Henkel packs carry the risk. The first is the 12% of packaging that Henkel counts as not yet designed for recycling, which, at 2.4 points a year, needs redesign on a timetable that runs into the same 2028 to 2030 window as the EU criteria. The second is the excluded products whose residue may harm recycling, which the PPWR does not exclude. The third is packs designed for recycling under Henkel’s criteria that may land in grade C rather than B, and so face a second redesign before 2038.

Henkel’s sustainable packaging page sets out the position it takes in policy debates on recyclability and fees.

“We advocate for effective eco-modulation within Extended Producer Responsibility (EPR) schemes.”

Henkel, company statement, Sustainable packaging, consulted 10 November 2026

The same page says Henkel wants frameworks that cut packaging weight and improve end-of-life recyclability. Recital 35 of the PPWR, as SPI’s record PR-EU-010 summarises it, ties fee modulation to the same performance grades, so a company that asks for eco-modulation is asking for fees that will reward its grade A and B packs and charge more for the rest.

A framework: four kinds of Henkel packaging under the rules

To turn the report into a work plan, SPI groups Henkel’s packaging by two questions: does Henkel publish a figure for it, and does a binding rule test it on a known date? Exhibit 7 sets out the four positions.

Exhibit 7SPI's report-versus-rule matrix: Henkel publishes figures for the packs that are ahead and says least about the ones the rules test next
PositionHenkel figure published?Binding test with a date?Henkel examplesRule
1. Shown and aheadYesYesEuropean detergent bottles at 65% PCRPR-EU-004
2. Shown and behindYesYesAdhesives Construction packs at 12%; 12% of packaging not designed for recyclingPR-EU-004, PR-EU-010
3. Excluded by Henkel, tested by lawNoYesProducts whose residue may harm recycling; dangerous goods packs outside transport usePR-EU-010
4. Not measuredNoYesVirgin plastic tonnage for SB 54; reusable transport packaging share; LUCID tonnagesPR-US-004, PR-EU-006, PR-DE-001

Source: SPI analysis of Henkel Sustainable Impact Report 2025, Henkel sustainable packaging page and SPI tracker records PR-EU-004, PR-EU-006, PR-EU-010, PR-US-004 and PR-DE-001 (SPI summary), checked 22 Nov 2026.

Positions are SPI's reading of published information, not an assessment of compliance. A rule test is binding when it has a date in force law; draft bills are not counted. Not legal advice.

Position 1, shown and ahead. These are the packs Henkel names in its report. They are safe against the 2030 recycled content floor and are where Henkel’s buyers will hold suppliers to the current specification rather than push for more.

Position 2, shown and behind. These are the packs where suppliers should expect the most change between now and 2030: higher PCR in construction and adhesive packaging and redesign of the packaging not yet designed for recycling. Henkel has published targets for both, so the direction is clear even where the path is not.

Position 3, excluded by Henkel, tested by law. These packs sit outside Henkel’s own measures, so they are not in the 88% or the 28%. The rules, however, do not exempt them in the same terms. This is the position where a gap between company reporting and legal exposure is most likely to surprise a reader of the report.

Position 4, not measured. Here the rule tests something Henkel does not publish at all. SB 54 tests plastic tonnage against a 2023 baseline. PPWR Article 29 tests the share of reusable transport packaging from 2030. Germany’s VerpackDG requires LUCID registration and, above set thresholds, a yearly completeness declaration. None of those numbers appears in the report.

Scenarios: what Henkel's 2030 share means for 2040

Henkel’s recycled target stops at 2030; the PPWR’s does not. Exhibit 8 runs three paces for the group share to 2030 and shows the pace that would then be needed to reach 65% by 2040, the floor for plastic packaging outside the food-contact and bottle categories.

Exhibit 8SPI calculation: on any pace Henkel has shown, the 2030 to 2040 step to 65% is steeper than the step to 35%
ScenarioYearly gain to 2030 (points)Group share in 2030 (%)Yearly gain then needed to reach 65% by 2040 (points)
Low1.0033.003.20
Base, Henkel target1.4035.003.00
High, 2025 pace3.0043.002.20

Source: SPI calculation from Henkel Sustainable Impact Report 2025 and Henkel releases; 2040 floor from the European Parliament Legislative Observatory summary (SPI summary), checked 22 Nov 2026.

Low assumes 1.00 point a year, below any year Henkel has reported since 2022. Base assumes the 1.40 points a year that the 35% target needs. High assumes 3.00 points a year, Henkel's 2024 to 2025 gain. Pace to 2040 = 65 minus the 2030 share, divided by ten years. The group average is not the PPWR test, which applies per plastic part; the comparison shows scale only.

On the base case, Henkel’s share would need to grow more than twice as fast after 2030 as before it, 3.00 points a year against 1.40, by SPI’s calculation. Only on the high case does the 2030 to 2040 step look like the pace Henkel has already shown. SPI analysis: a 35% target for 2030 is cautious against the company’s own record, and the arithmetic suggests the lowest-cost route to the 2040 floor is to keep the recent pace rather than slow down to the target.

Two cautions apply. The PPWR test is per plastic part, so a group average of 65% would not guarantee that every pack meets it. And the PPWR counts post-consumer recycled plastic only; Henkel’s report does not say what share of its recycled plastic is post-consumer, although each product example names PCR.

Henkel Sustainable Impact Report against US state rules

Henkel’s North American consumer brands include Persil, Snuggle and Dial. The report says compact formulas and packaging there save an estimated 1,300 tonnes of plastic and 4,000 tonnes of transport CO2 a year, and the sustainable packaging page says that since 2025 all of Henkel’s liquid laundry detergent brands in North America have included at least 50% recycled plastic in the bottle bodies.

California’s SB 54 tests different things. Exhibit 9 sets out its targets, as CalRecycle lists them, beside the closest Henkel disclosure.

Exhibit 9California's SB 54 tests tonnage and recycling rates; Henkel's report publishes neither for the US
DateSB 54 targetClosest Henkel disclosure
1 Jan 202710% less single-use plasticCompact formats save about 1,300 tonnes of plastic a year in North America; no baseline given
1 Jan 202830% of single-use plastic recycledno data
1 Jan 203020% less single-use plastic; 40% recycledHenkel 2030 targets: 35% recycled plastic, 100% designed for recycling
1 Jan 203225% less single-use plastic; 65% recycled; 100% recyclable or compostableNo Henkel target beyond 2030

Source: CalRecycle SB 54 Producer Guidance; SPI tracker record PR-US-004; Henkel Sustainable Impact Report 2025, p. 44; Henkel sustainable packaging page (SPI summary), checked 22 Nov 2026.

SB 54 targets apply to covered single-use packaging and plastic food service ware in California, with source reduction measured against a 2023 baseline under the regulations. The recycling rate targets apply statewide, not per producer. Henkel's figures are North American or global. Not legal advice.

The permanent SB 54 regulations took effect on 1 May 2026 and gave producers until 1 June 2026 to join Circular Action Alliance, register as an independent producer or apply for a small producer exemption, according to SPI’s record PR-US-004. Producers of single-use plastic packaging also fund the Plastic Pollution Mitigation Fund, USD 500 million a year for ten years from July 2027. SPI has not yet confirmed which Henkel entity is the producer of record in California or which route it chose.

SPI analysis

The 1,300 tonne saving is the only plastic tonnage in Henkel’s US disclosures, and it is a yearly saving, not a footprint. SB 54’s source reduction steps need a 2023 baseline in tonnes and in units. Suppliers of bottles, caps and films to Henkel’s US business should expect the request for that data to come through the producer responsibility organisation’s reporting rather than through the sustainability report.

Other US states bring other tests. Ledger 29 works through Oregon and Colorado EPR fees and New Jersey’s recycled content law for home care packs; that analysis applies to Henkel’s detergent jugs and is not repeated here. SPI’s California SB 54 Ledger explains the baseline and the PRO plan.

Germany, Australia and the logistics chain

Henkel is headquartered in Düsseldorf, and its SPI profile links its household packaging to Germany’s VerpackDG, recorded as PR-DE-001. The Act replaced the Verpackungsgesetz on 12 August 2026, after the Bundestag passed it on 11 June 2026 and the Bundesrat let it pass on 10 July 2026. Registration in the LUCID register continues, and producers above 80 tonnes of glass, 50 tonnes of paper and board or 30 tonnes of other materials a year file a completeness declaration by 15 May, according to SPI’s record. The Zentrale Stelle sets out one change for sellers based abroad: its page What will change from 12 August says an authorised representative must be named in the LUCID Packaging Register at the time of initial registration. That duty reaches producers without a German branch who sell directly to German end users, so it bears on Henkel’s foreign suppliers and online sellers of its brands more than on Henkel itself. Exhibit 10 maps the duties in the markets SPI’s Henkel profile covers.

Exhibit 10Henkel's packaging duties by market: in force in the EU, Germany and California, still a bill in Australia
MarketRuleStatusNext dated stepHenkel packs in scope
European UnionPPWR, PR-EU-001Applies since 12 Aug 2026Recycled content method act due 31 Dec 2026Detergent bottles, refill pouches, adhesive tubes
European UnionRecycled content, PR-EU-0042030 tier ahead2030 tierPlastic packs outside food contact
European UnionRecyclability, PR-EU-010Article 6(1) applies; grades laterCriteria acts due 1 Jan 2028All packaging, 12% not yet designed for recycling
European UnionRe-use, PR-EU-006Targets from 1 Jan 2030Calculation rules due 30 Jun 2027Transport packaging, including B2B adhesive shipments
GermanyVerpackDG, PR-DE-001Applies since 12 Aug 2026Completeness declaration by 15 May 2027Household laundry and hair care packs
CaliforniaSB 54, PR-US-004Regulations in effect since 1 May 202610% source reduction, 1 Jan 2027Detergent jugs, soap bottles
AustraliaEPR bill, PR-AU-003Referred to Senate committee 14 May 2026Report was due 6 Aug 2026; none listedBottles of 4 litres and smaller at 75% PCR

Source: SPI tracker records PR-EU-001, PR-EU-004, PR-EU-006, PR-EU-010, PR-DE-001, PR-US-004 and PR-AU-003; SPI Packaging Buyers Database, Henkel profile; Parliament of Australia inquiry page (SPI summary), checked 13 Oct 2026.

Status as of 10 November 2026. Henkel examples come from Henkel's own pages or SPI's profile. SPI has not yet confirmed Henkel's legal entities in each market. Not legal advice.

In Australia, the Extended Producer Responsibility Scheme for Packaging (No Time to Waste) Bill 2026 was referred to the Senate Environment and Communications Legislation Committee on 14 May 2026 with a reporting date of 6 August 2026. On 10 November 2026 the inquiry page still shows the status Inquiry referred and lists no tabled report. The bill creates no duties until it passes. Henkel’s move from 50% to 75% PCR in Australian and New Zealand bottles of 4 litres and smaller puts those packs well above any recycled content floor discussed there so far.

In the logistics chain, PPWR Article 29 requires users of transport packaging to make at least 40% of it reusable within a re-use system from 1 January 2030 (PR-EU-006). Henkel’s report publishes no reusable transport share. Its sustainable packaging page records 130,000 pounds of wooden pallets donated in Greenville and Enoree in North America and more than 5,000 tons of silicone carrier paper, as Henkel states it, recycled to date in Consumer Brands in the EU, both waste measures rather than reuse measures. Ledger 60 covers the re-use duty in detail.

Industry reaction

Henkel’s own words frame its packaging policy around EPR rather than around the PPWR as such.

“Our ambition in line with the framework of Extended Producer Responsibility (EPR) is to help prevent the unregulated disposal of packaging waste.”

Henkel, company statement, Sustainable packaging, consulted 10 November 2026

The sentence repeats, almost word for word, the third pillar on page 50 of the report. It treats EPR as the system that finances collection, which is where Henkel’s partnerships sit: it is a founding member of CEFLEX, a consortium of more than 130 European companies and organisations working on flexible packaging, and it lists the Ellen MacArthur Foundation’s Global Commitment 2030, the Recyclate Forum and the US Plastics Pact among its memberships. The packaging chapter also names the Packaging Recyclabs at Henkel’s customer centres in Düsseldorf and Shanghai, where Adhesive Technologies tests adhesives for recyclable packaging.

The 14 April 2026 release places packaging inside a wider set of 2030 goals: 42% lower scope 1 and 2 emissions and 30% lower scope 3 emissions against 2021, net zero by 2045, and 85% of suppliers meeting sustainability criteria. Henkel’s chief executive described responsible practice and strong business performance as going hand in hand. The release does not mention the PPWR, SB 54 or any other packaging law.

SPI analysis

For a group whose 2025 report predates the PPWR’s application by four months, the silence on the Regulation is unsurprising. The 2026 report, due in spring 2027, will be the first written with the PPWR in force, and the place to look for any change in scope, method or exclusions.

Exhibit 11From Henkel's 2022 baseline year to the 2040 PPWR tier: the dates that govern its packaging, past and next
  • past
  • next
Exhibit 11. From Henkel's 2022 baseline year to the 2040 PPWR tier: the dates that govern its packaging, past and next13 dated items from 7 Mar 2023 to 1 Jan 2040.2023202520272029203120332035203720392041Today7 Mar 2023: Henkel reports 2022: about 16% recycled plastic, about 87% designed for recycling and reuse11 Mar 2025: Henkel reports 2024: 25% recycled plastic, 89% designed for recycling14 Apr 2026: Sustainable Impact Report 2025 and new 2030 targets published1 May 2026: California SB 54 permanent regulations take effect14 May 2026: Australian packaging EPR bill referred to Senate committee12 Aug 2026: PPWR and Germany's VerpackDG apply31 Dec 2026: PPWR recycled content calculation act due1 Jan 2027: SB 54 step: 10% less single-use plastic15 May 2027: VerpackDG completeness declarations due2028: Adhesives Construction target of 45% recycled content1 Jan 2028: PPWR design-for-recycling criteria acts due1 Jan 2030: PPWR 2030 tiers, re-use targets; Henkel 2030 targets1 Jan 2040: PPWR 2040 tier: 65% for other plastic packagingExhibit 11. From Henkel's 2022 baseline year to the 2040 PPWR tier: the dates that govern its packaging, past and next13 dated items from 7 Mar 2023 to 1 Jan 2040.2023202620292032203520382041Today7 Mar 2023: Henkel reports 2022: about 16% recycled plastic, about 87% designed for recycling and reuse11 Mar 2025: Henkel reports 2024: 25% recycled plastic, 89% designed for recycling14 Apr 2026: Sustainable Impact Report 2025 and new 2030 targets published1 May 2026: California SB 54 permanent regulations take effect14 May 2026: Australian packaging EPR bill referred to Senate committee12 Aug 2026: PPWR and Germany's VerpackDG apply31 Dec 2026: PPWR recycled content calculation act due1 Jan 2027: SB 54 step: 10% less single-use plastic15 May 2027: VerpackDG completeness declarations due2028: Adhesives Construction target of 45% recycled content1 Jan 2028: PPWR design-for-recycling criteria acts due1 Jan 2030: PPWR 2030 tiers, re-use targets; Henkel 2030 targets1 Jan 2040: PPWR 2040 tier: 65% for other plastic packaging
  1. Henkel reports 2022: about 16% recycled plastic, about 87% designed for recycling and reusepast
  2. Henkel reports 2024: 25% recycled plastic, 89% designed for recyclingpast
  3. Sustainable Impact Report 2025 and new 2030 targets publishedpast
  4. California SB 54 permanent regulations take effectpast
  5. Australian packaging EPR bill referred to Senate committeepast
  6. PPWR and Germany's VerpackDG applypast
  7. PPWR recycled content calculation act duenext
  8. SB 54 step: 10% less single-use plasticnext
  9. VerpackDG completeness declarations duenext
  10. 2028Adhesives Construction target of 45% recycled contentnext
  11. PPWR design-for-recycling criteria acts duenext
  12. PPWR 2030 tiers, re-use targets; Henkel 2030 targetsnext
  13. PPWR 2040 tier: 65% for other plastic packagingnext

Source: Henkel releases and Sustainable Impact Report 2025; Commission Notice C/2026/3084; CalRecycle; Zentrale Stelle Verpackungsregister; Parliament of Australia; SPI tracker records (SPI summary), checked 22 Nov 2026.

Category shows past or next from 10 November 2026. The date of Henkel's next report is an SPI expectation from its past publication dates, not a company statement. Not legal advice.

Show the data
Exhibit 11. From Henkel's 2022 baseline year to the 2040 PPWR tier: the dates that govern its packaging, past and next
DateLabelCategoryLink
2023-03-07Henkel reports 2022: about 16% recycled plastic, about 87% designed for recycling and reusepasthttps://www.henkel.com/press-and-media/press-releases-and-kits/2023-03-07-henkel-drives-progress-in-sustainability-with-improvements-in-climate-protection-and-social-engagement-1807118
2025-03-11Henkel reports 2024: 25% recycled plastic, 89% designed for recyclingpasthttps://www.henkel.com/press-and-media/press-releases-and-kits/2025-11-03-henkel-makes-further-progress-across-all-areas-of-its-sustainability-strategy-2044862
2026-04-14Sustainable Impact Report 2025 and new 2030 targets publishedpasthttps://www.henkel.com/press-and-media/press-releases-and-kits/2026-04-14-henkel-announces-new-sustainability-targets-for-2030-2148156
2026-05-01California SB 54 permanent regulations take effectpasthttps://calrecycle.ca.gov/packaging/packaging-epr/producerguidance/
2026-05-14Australian packaging EPR bill referred to Senate committeepasthttps://www.aph.gov.au/search/url/Inquiry/27382_16_
2026-08-12PPWR and Germany's VerpackDG applypasthttps://www.verpackungsregister.org/en/i-want-to-know-what-will-change-from-12-august
2026-12-31PPWR recycled content calculation act duenexthttps://green-forum.ec.europa.eu/packaging-and-packaging-waste-regulation-implementation_en
2027-01-01SB 54 step: 10% less single-use plasticnexthttps://calrecycle.ca.gov/packaging/packaging-epr/producerguidance/
2027-05-15VerpackDG completeness declarations duenexthttps://www.verpackungsregister.org/en/i-want-to-know-what-will-change-from-12-august
2028-01-01PPWR design-for-recycling criteria acts duenexthttps://eur-lex.europa.eu/legal-content/EN/TXT/PDF/?uri=CELEX:52026XC03084
2028Adhesives Construction target of 45% recycled contentnexthttps://www.henkel.com/sustainability/sustainable-packaging
2030-01-01PPWR 2030 tiers, re-use targets; Henkel 2030 targetsnexthttps://www.henkel.com/resource/blob/2147522/8941c6fb4e08be9facee9fd4ee20ae64/data/sustainable-impact-report-2025-en.pdf
2040-01-01PPWR 2040 tier: 65% for other plastic packagingnexthttps://oeil.europarl.europa.eu/oeil/en/document-summary?id=1784253

What leaders should do now

  1. Account managers at Henkel packaging suppliers, before Henkel’s next report in spring 2027: ask whether the 88% covers Adhesive Technologies as well as Consumer Brands, and how the near 100% Consumer Brands figure relates to it.
  2. Bottle, cap and sleeve suppliers for Henkel’s European laundry brands, during 2027 planning: document the recycled content of every plastic part of 5% or more of unit weight, since Article 7 tests each part and Henkel’s 65% covers bottle bodies only.
  3. Suppliers of tubs, cartridges and tubes to Henkel’s construction adhesives, now: prepare PCR grades and supply volumes that reach 45% by 2028, since that target sits 10 points above the 35% PPWR floor for 2030.
  4. Packaging engineers working on Henkel’s excluded products, before the criteria acts due 1 January 2028: list packs whose residue may affect recyclability, and test them against the draft PPWR criteria, since the Regulation does not share Henkel’s exclusion.
  5. Compliance leads for Henkel lines sold in California, by 1 January 2027: confirm the 2023 tonnage and unit baseline reported through the producer responsibility organisation, since the report gives no virgin plastic figure.
  6. Logistics managers moving Henkel B2B shipments in the EU, by the calculation rules due 30 June 2027: measure the current share of reusable pallets, drums and intermediate bulk containers against the 40% target for 2030.
  7. ESG analysts covering Henkel, at the 2027 reporting season: ask for a post-consumer share of recycled plastic, a plastic tonnage and a regional split, the three numbers that would let the report be read against the rules.

Questions for your board

  • Which of the packs we make for Henkel are in the 28% and the 88%, and which sit in the exclusions?
  • Do our caps, sleeves and labels for Henkel bottles meet a recycled content floor on their own, or only as part of a bottle average?
  • Can we supply the PCR volumes that a move from 12% to 45% in construction adhesive packs implies by 2028?
  • If Henkel’s design target narrows its scope again, which of our formats would it drop and which would it redesign?
  • Do we hold the 2023 tonnage data that a California source reduction claim would need?
  • Are our transport packaging flows with Henkel measured in a way that Article 29 will accept?

What to watch

  • 31 Dec 2026: the Commission’s PPWR recycled content calculation act is due, which will set how Henkel and its suppliers count PCR per part and per plant.
  • 1 Jan 2027: California’s first SB 54 step of 10% less single-use plastic.
  • Spring 2027, date not set: Henkel’s report for 2026, the first written with the PPWR in force; SPI expects it from past dates, but Henkel has not announced it.
  • 15 May 2027: Germany’s first VerpackDG completeness declarations under the new Act.
  • 30 Jun 2027: PPWR re-use calculation rules due.
  • 1 Jan 2028: PPWR design-for-recycling criteria acts due.
  • 2028, by year end at the latest: Henkel’s Adhesives Construction target of 45% recycled content.

Methodology

  • Data used: Henkel’s Sustainable Impact Report 2025 (14 April 2026), its release of the same day, its sustainable packaging page, and its releases of 7 March 2023, 4 March 2024 and 11 March 2025, all consulted on 10 November 2026; the European Parliament Legislative Observatory summary; the German text of PPWR Article 7 as reproduced by LX Gesetze; CalRecycle’s SB 54 producer guidance; the Zentrale Stelle Verpackungsregister; the Parliament of Australia inquiry page; SPI tracker records PR-EU-001, PR-EU-004, PR-EU-006, PR-EU-010, PR-DE-001, PR-US-004 and PR-AU-003 and the Henkel profile in the SPI Packaging Buyers Database, data as of 14 October 2026.
  • Company figures: every Henkel figure is the company’s own, as first published, not audited by SPI. Henkel gives the 2022 figures as approximate.
  • Calculations: labelled SPI calculation. Past pace divides the change from 2022 to 2025 by three years; needed pace divides the gap to the 2030 target by five years; scenario paces are stated assumptions. Day counts run from 10 November 2026. No figures are summed or compared across currencies.
  • PPWR text: the 2030 floors other than the drinks bottle figure come from an unofficial German text (LX Gesetze) and have not yet been confirmed by SPI against the Official Journal. Exemptions come from the Commission Notice C/2026/3084 and the EUR-Lex summary as recorded in SPI’s tracker.
  • Cut-off: 10 November 2026.
  • Limitations: SPI has not yet confirmed the boundary of Henkel’s 88% figure, the post-consumer share of its 28%, the recycled content of caps and sleeves, Henkel’s producer entities and routes in California and Germany, or where the Ceresit CE40 and CE43 packs are sold. Nothing here is legal advice or investment advice.

FAQ

What is the Henkel Sustainable Impact Report?

It is Henkel’s annual sustainability report. The 2025 edition was published on 14 April 2026, with data closed on 31 December 2025. Its packaging chapter reports 28% recycled plastic in consumer goods packaging, 88% of packaging designed for recycling or reusability and 98% of paper and cardboard recycled or from sustainable origins.

Did Henkel meet its 2025 packaging targets?

No. Henkel reported 28% recycled plastic against a goal of more than 30%, 88% designed for recycling or reusability against 100%, and 98% sustainable paper and cardboard against 100%. The report gives no achieved figure for its aim to cut fossil-based virgin plastic by 50%. It shows each goal beside its result.

What are Henkel's 2030 packaging targets?

On 14 April 2026 Henkel set at least 35% recycled plastic in packaging for consumer products, excluding dangerous goods, and 100% of packaging designed for recycling, excluding dangerous goods and products whose residue may affect recyclability. By SPI’s calculation these need 1.4 and 2.4 points a year from the 2025 results.

How fast has Henkel's recycled plastic share grown?

Henkel’s releases give about 16% for 2022, 19% for 2023, 25% for 2024 and 28% for 2025. By SPI’s calculation that is an average gain of 4.0 points a year. In March 2025 Henkel said it expected to reach 30% by the end of 2025; it reported 28%.

Does Henkel meet the PPWR recycled content rules?

The PPWR recycled content floors apply from the 2030 tier and per plastic part, so no pack is tested yet. Henkel’s European detergent bottle bodies at 65% PCR already exceed the 35% floor for 2030 in the German text. Its construction adhesive packs, at 12% in 2025, are below it.

Why did Henkel drop reuse from its design target?

Henkel’s report and release give no reason for the change. Its 2025 goal counted packaging designed for recycling or reusability, while its 2030 target counts design for recycling only. Reuse duties in the EU are set separately, through PPWR Article 29 targets for transport and grouped packaging from 2030.

Sources

  1. Henkel, Sustainable Impact Report 2025, 14 April 2026, consulted 2026-11-10.
  2. Henkel, Henkel announces new sustainability targets for 2030, 14 April 2026, consulted 2026-11-10.
  3. Henkel, Sustainable packaging, consulted 2026-11-10.
  4. Henkel, Henkel makes further progress across all areas of its sustainability strategy, 11 March 2025, consulted 2026-11-10.
  5. Henkel, Strong progress on Henkel’s sustainability goals, 4 March 2024, consulted 2026-11-10.
  6. Henkel, Henkel drives progress in sustainability with improvements in climate protection and social engagement, 7 March 2023, consulted 2026-11-10.
  7. European Commission, Notice C/2026/3084, guidance on Regulation (EU) 2025/40, OJ C 10 June 2026, as recorded in SPI tracker records PR-EU-001, PR-EU-004, PR-EU-006 and PR-EU-010, data as of 2026-10-14.
  8. European Parliament Legislative Observatory, summary of the first-reading position on packaging and packaging waste, 24 April 2024, consulted 2026-11-10.
  9. LX Gesetze, PPWR Article 7, German text (unofficial), consulted 2026-11-10.
  10. EUR-Lex, Summaries of EU legislation, Packaging and packaging waste, as recorded in SPI tracker record PR-EU-004, data as of 2026-10-14.
  11. European Commission Green Forum, PPWR implementation timeline, as recorded in SPI tracker records, data as of 2026-10-14.
  12. CalRecycle, SB 54 Producer Guidance, consulted 2026-11-10.
  13. CalRecycle, SB 54 permanent regulations approved and in effect, 1 May 2026, as recorded in SPI tracker record PR-US-004, data as of 2026-10-14.
  14. CalEPA, SB 54 Plastic Pollution Mitigation Fund, as recorded in SPI tracker record PR-US-004, data as of 2026-10-14.
  15. Zentrale Stelle Verpackungsregister, What will change from 12 August, consulted 2026-11-10.
  16. Bundesrat, Drucksache 377/26, Gesetzesbeschluss on the VerpackDG, as recorded in SPI tracker record PR-DE-001, data as of 2026-10-14.
  17. Parliament of Australia, Senate inquiry, Extended Producer Responsibility Scheme for Packaging (No Time to Waste) Bill 2026, consulted 2026-11-10.
  18. SPI Regulation Tracker, PR-EU-004 and linked records PR-EU-001, PR-EU-006, PR-EU-010, PR-DE-001, PR-US-004 and PR-AU-003, data as of 2026-10-14.
  19. SPI Packaging Buyers Database, Henkel profile, data as of 2026-10-14.

Go deeper

More from SPI Ledger

All articles
  1. News analysis

    Amazon sustainability report packaging: plastic in 27% of North America shipments and 74,073 tonnes

    The Amazon sustainability report packaging figures, in the 2025 Sustainability Report that Amazon announced on 1 July 2026, show single-use plastic delivery packaging in 27% of North America shipments in 2025, down…

    19 min read

  2. News analysis

    Marico sustainability report packaging: 95% recyclable, 14.9% recycled plastic and EPR in three markets

    The Marico sustainability report packaging figures, in its ESG Data Book for FY 2025-26, show 95% of packaging by weight recyclable against a 100% goal first dated 2025 and now dated 2030,…

    19 min read

  3. News analysis

    ITC sustainability report plastic: 73,762 tonnes, 3.22% recycled content and a 2030 rigid and flexible gap

    The ITC sustainability report plastic figures for 2025-26, set out in the ESG Fact Book that accompanies the ITC Sustainability Report 2026, show 73,762 tonnes of plastic packaging placed on the market,…

    20 min read

ClosingAsk the SPI team

Ask the SPI team

What changes for your packaging next quarter?

Tell us your markets and materials. The SPI team walks you through the rules and buyer commitments that affect them.

Prefer email? Write to sales@strategicpackaginginsights.com.

Questions people bring
  1. Q1

    Which packaging rules apply to us in each market we sell in?

    We map each market's EPR, tax, ban, recycled-content, labelling and deposit rules against your materials and formats, and show which are in force, adopted or only proposed.

  2. Q2

    What could EPR fees and plastic taxes cost us next year?

    We apply published fee tables and tax rates to your tonnages and recycled content, and show the result as scenarios with every rate sourced.

  3. Q3

    Can you tell us when a rule changes?

    Yes. The free tracker alerts cover rule changes by country; a monitoring retainer adds monthly notes on what the changes mean for your portfolio.